Manufacturer since 20033,000 m² factory in Shenzhen5 production lines100,000 power supplies / monthOEM & ODM, factory direct
Wireless & USB-C

GaN vs Silicon Chargers: A Sourcing Guide for Distributors

Written by engineers at the Daxpoo factory, Shenzhen · · 4 min read

Gallium nitride (GaN) has gone from a premium feature to a standard spec in USB-C chargers. For distributors and brand owners the question is no longer “should we sell GaN?” but “where does GaN make sense, and what should we check when we buy it?” This guide answers both from a manufacturer’s point of view.

What GaN changes inside a charger

Every switching power supply uses transistors to switch current on and off many thousands of times per second. Traditional chargers use silicon MOSFETs. GaN transistors can switch faster with lower losses. That allows:

  • Smaller magnetics: higher switching frequency means a smaller transformer.
  • Less heat: lower losses mean less heat to get rid of, so the enclosure can shrink.
  • Higher power density: 65W in a size that used to hold 30W.

GaN vs silicon at a glance

GaN Silicon
Size at 65W Compact, often pocketable Larger brick
Heat at full load Lower losses Higher losses
Bill of materials Higher component cost Lower, mature supply chain
Best range 45W–240W Up to about 30W, or where size is not critical
Multi-port designs Well suited Become bulky

Where GaN makes commercial sense

  • 65W laptop chargers: the sweet spot for business and student laptops, and the size difference is obvious to end users.
  • 100W–140W multi-port chargers: one charger for laptop, phone and tablet.
  • Travel chargers where weight and size sell the product.

For 18W–25W phone chargers, silicon is usually cheaper and the size gain from GaN is small. Many distributors sell silicon at the entry level and GaN from 45W upward.

What to check when sourcing GaN chargers

  1. Thermal performance: ask for case temperature at full load after one hour. Small chargers can run hot if the design is pushed too far.
  2. Power sharing on multi-port models: how is power split when two or three devices are connected? Ask for the table.
  3. USB PD compliance: correct power negotiation with a range of laptops and phones, not just one test device.
  4. Protection: over-voltage, over-current, short-circuit and over-temperature protection.
  5. Certification: CE, FCC, RoHS and efficiency reports for the exact model.
  6. Component stability: confirmation that the GaN device and controller will not change between batches without notice.

The market is moving to USB-C

Since the EU common charger rules started covering laptops on 28 April 2026, USB-C has become the default for new laptops sold in Europe. GaN is the technology that makes small, high-wattage USB-C chargers possible. Read more in our article on the EU common charger rule for laptops.

How to read a multi-port power table

A “140W three-port GaN charger” rarely delivers 140W to every port at once. Good suppliers publish a power distribution table, for example:

Ports in use Typical split
C1 only Up to the full rating
C1 + C2 Laptop priority on C1, phone-level power on C2
C1 + C2 + A Reduced power on C1, basic power on C2 and A

Put this table on your packaging and listings. It reduces returns from customers who expected full power on every port.

Testing GaN samples before you order

  1. Interoperability: charge at least five popular laptops and phones and confirm each negotiates the expected voltage.
  2. Thermal: run at full rated output for one hour in a 25°C room and measure the case temperature.
  3. Hot-plug behaviour: connect and disconnect a second device while a laptop is charging. Cheap designs briefly cut power to all ports.
  4. Noise: listen for coil whine at light load, which some users notice at night.
  5. Cable: check that the cable supplied is rated for the charger’s maximum current.

Pricing reality

GaN components still cost more than silicon equivalents, but the gap has narrowed sharply as volumes have grown. For 65W and above, the smaller housing and lighter shipping weight often offset part of the component cost. Expect a reasonable premium for GaN at the same wattage, and be cautious of GaN chargers priced at or below good silicon models: the savings usually come from thermal design or protection circuits.

Building a simple GaN range

A distributor can cover most demand with four SKUs:

  • 30W–35W single USB-C for phones and tablets
  • 65W single or dual USB-C for most laptops
  • 100W multi-port for 15–16 inch laptops and desk setups
  • 140W multi-port for performance laptops using USB PD 3.1

Add regional plug variants and a quality cable for each, and the range covers both new USB-C laptops and the phones and tablets that travel with them.

Private label GaN from our factory

We build USB-C PD and GaN chargers from 20W to 140W in our Shenzhen factory, with your logo, plug type and packaging. Every unit is tested and burned in before shipping. Send your target wattages and volumes through the quote form for factory pricing, or see OEM vs ODM to decide how much customisation you need.

Frequently asked questions

Are GaN chargers better than silicon chargers?

GaN chargers can be smaller and run more efficiently at the same wattage, which is why they dominate compact 65W to 140W designs. Below about 30W the size advantage is small and silicon is often the better value.

Are GaN chargers safe?

A well-designed GaN charger is as safe as a silicon one. Safety depends on the overall design, thermal management, protection circuits and certification, not on the transistor material alone.

Which GaN wattages should a distributor stock?

65W single-port and 100W to 140W multi-port models cover most laptop and multi-device demand. Add a 30W to 45W model for phones and tablets.

Daxpoo power adapter assembly line with operators at ESD workstations
Our assembly line, Shenzhen

We manufacture what we write about

These guides come from the people who design, build and test chargers on our factory floor. Send your spec and quantity for factory pricing.

More guides: Wireless & USB-C

Request a factory quote

You are writing to the factory, not a reseller. Send the model or spec and quantity; a sales engineer replies within one working day with factory pricing and lead time.

We use your details only to answer this request. Privacy policy

WhatsApp us